Netopia 4522 T1 Manuel d'utilisateur

Netopia ™ 4522 T1 Router Getting Started Guide M AKING B ROADBAND W ORK ™

2-4 Getting Started Guide Netopia 4522 back panel .1. Connect the mini-DIN8 connector from the power adapter to the power port, and plug the other e

Making the Physical Connections 2-5 Netopia 4522 T1 Router Status Lights The figure below represents the Netopia 4522 status light (LED) panel. Neto

2-6 Getting Started Guide

Connecting to Your Local Area Network 3-1CCCChhhhaaaapppptttteeeerrrr 3333CCCCoooonnnnnnnneeeeccccttttiiiinnnngggg ttttoooo YYYYoooouuuurr

3-2 Getting Started Guide Once the Netopia 4522 is properly configured and connected to your LAN, PC and Macintosh computers that have their required

Sharing the Connection 4-1CCCChhhhaaaapppptttteeeerrrr 4444SSSShhhhaaaarrrriiiinnnngggg tttthhhheeee CCCCoooonnnnnnnneeeeccccttttiiiioooonn

4-2 Getting Started GuideDynamic configuration (recommended)To configure your PC for dynamic addressing do the following:Note: You can also use these i

Sharing the Connection 4-3Static configuration (optional)If you are manually configuring for a fixed or static IP address, perform the following:1. Go

4-4 Getting Started Guide4. Click OK in this window and the next window. When prompted, reboot the computer.Note: You can also use these instructions

Sharing the Connection 4-5Configuring TCP/IP on Macintosh ComputersThe following is a quick guide to configuring TCP/IP for MacOS computers. Configurin

Copyright ©2002 Netopia, Inc., v.082702All rights reserved. Printed in the U.S.A.This manual and any associated artwork, software, and product design

4-6 Getting Started GuideStatic configuration (optional)3. In the TCP/IP window or in the MacTCP/More window, select or type information into the field

Sharing the Connection 4-7Note: You can use these instructions to configure other computers on your network to accept IP addresses served by the Neto

4-8 Getting Started Guide

Console-Based Management 5-1CCCChhhhaaaapppptttteeeerrrr 5555CCCCoooonnnnssssoooolllleeee----BBBBaaaasssseeeedddd MMMMaaaannnnaaaaggggeeeemmmm

5-2 Getting Started Guidemay be using the router to connect to more than one service provider or remote site. The System Configuration menus display

Console-Based Management 5-3Configuring Telnet softwareIf you are configuring your router using a Telnet session, your computer must be running a Teln

5-4 Getting Started GuideLaunch your terminal emulation software and configure the communications software for the values shown in the table below. Th

Easy Setup 6-1CCCChhhhaaaapppptttteeeerrrr 6666EEEEaaaassssyyyy SSSSeeeettttuuuuppppThis chapter describes how to use the Easy Setup console s

6-2 Getting Started GuideIf you do not see the Main Menu, verify that: If you are using a serial connection, that your serial port speed is the same

Easy Setup 6-3Quick Easy Setup Connection PathThis section may be all you need to do to configure your Netopia 4522 T1 Router. Your service provider

Contents 3 G Chapter 1 — Introduction... 1-1 Overview ...

6-4 Getting Started Guide❑ RFC1483 RFC1483 Mode:❑ Bridged 1483 (default) or❑ Routed 1483(for Bridged 1483 only)PPP over Ethernet (PPPoE)❑ Off (defaul

Easy Setup 6-5The following steps will get you up and running quickly:1. Open a Telnet session to 192.168.1.1 to bring up the Main Menu.If you don&a

6-6 Getting Started GuideT1 Line ConfigurationThe T1 Line Configuration screen appears.1. Select Operation Mode and press Return. From the pop-up menu,

Easy Setup 6-77. Select Channel Data Rate and highlight the data rate that your service provider has designated your channel to connect at. The chan

6-8 Getting Started GuideRouted 1483. If you select Bridged 1483, a new option PPP over Ethernet (PPPoE) appears. You can then toggle PPPoE On or Off

Easy Setup 6-9If you selected Numbered, the following fields appear. Select the editable field labeled Local WAN IP Address.The default address is 0.

6-10 Getting Started Guide1. Select Ethernet IP Address and enter the first IP address from the IP address range your ISP has given you. This will be

Easy Setup 6-117. Toggle IP Address Serving to On or Off, depending on whether you want the device’s IP address server to supply dynamic IP addresse

6-12 Getting Started GuideThe Router will restart and your configuration settings will be activated. You can then Exit or Quit your Telnet application

Technical Specifications and Safety Information -1AAAAppppppppeeeennnnddddiiiixxxx AAAATTTTeeeecccchhhhnnnniiiiccccaaaallll SSSSppppeeeecccciiii

4 Getting Started Guide Easy Setup Profile ... 6-8IP Easy Setup ...

-2 Getting Started GuideDecember 1, 2000 Canada – CSA: CAN/CSA-C22.2 No. 950-95EMI: FCC Part 15 Class B FCC Part 68Regulatory noticesWarningsThis

Technical Specifications and Safety Information -3Items (b) and (d) are indicated on the label. The Ringer Equivalence Number (REN) is used to determi

-4 Getting Started GuideImportant safety instructionsCaution Depending on the power supply provided with the product, either the direct plug-in powe

Limited Warranty and Limitation of Remedies-Revised January 2002LLLLiiiimmmmiiiitttteeeedddd WWWWaaaarrrrrrrraaaannnnttttyyyy aaaannnndddd LL

Introduction 1-1CCCChhhhaaaapppptttteeeerrrr 1111IIIInnnnttttrrrroooodddduuuuccccttttiiiioooonnnn Overview The Netopia 4522 T1 Router is a full-

1-2 Getting Started Guide Easy Setup with menu-driven interface Console Tiered Access, 2 levels of configuration access Configuration Management

Making the Physical Connections 2-1CCCChhhhaaaapppptttteeeerrrr 2222MMMMaaaakkkkiiiinnnngggg tttthhhheeee PPPPhhhhyyyyssssiiiiccccaaaallll

2-2 Getting Started Guide You will need: A Windows–based PC or a Macintosh computer with Ethernet connectivity for configuring the Netopia 4522. Th

Making the Physical Connections 2-3 Identify the Connectors and Attach the Cables Identify the connectors and switches on the back panel and attach